The Dewesoft KRYPTON® is a rugged and distributed EtherCAT data acquisition system. This system tracks field measurements in extreme and harsh environments. It has an IP67 rating and operates in temperatures from -40° to +85°C. It also has high shock protection thus making it perfect for rugged environments.
Metromatics proudly sell, support, and service the Dewesoft Product range in Australia and New Zealand.
This data acquisition system also uses 100 Mbit datalink thanks to its EtherCAT protocol technology. The KRYPTON®’S fast data bus allows users to daisy-chain KRYPTON® Units together. Furthermore, at the end of the chain, the RJ45 cable plugs into the Ethernet port of your PC or 8-pin LEMO connector. As a result, it’s able to connect to powerful computers liken the Krypton CPU, SBOX R2DB, R4 or R8.
In addition to this, the EtherCAT brings another big advantage – zero configuration. This is because KRYPTON® devices do not require any complex IP setup. This is in thanks to KRYPTON®’S Dewesoft X software which automatically recognises and sets up devices.
Finally, only a single cable required for data, power, and synchronization. This cable can run up to 100 metres from module to module connecting amplifiers together.
KRYPTON® data acquisition modules are small, rugged, and modular. As a result, they are perfect for field measurements in any environment and can fit perfectly in tight places near sensors. Therefore, by removing the need for cables users can save money, effort and avoid writing errors. This feature also helps users bring data acquisition closer to the origin of data, thus improving signal quality as a result.
KRYPTON® DAQ modules are robust. Their build consists of aluminium bricks and industrial-grade electronics. Additionally, thermally conductive, and electrically isolative rubber, seals the units. Finally, a rubber band around the KRYPTON chassis further protects it from shocks. As a result, it’s waterproof, shockproof and can withstand shocks up to 100G. Furthermore, the KRYPTON® can also operate in extremely harsh environments. For example, operating temperatures can span from -40°C to +85°C.
Distributed DAQ: KRYPTON® DAQ modules bring data acquisition closer to sensors and distribute DAQ modules down to a single input channel.
There are two types of families of KRYPTON devices:
KRYPTON ONE are single channel I/O Modules. Firstly, the smallest IP67 DAQ Module world wide that fit into a pocket. Therefore, ideal for those applications where modules need to be installed right next to the sensor in tight spaces.
KRYPTON ONE offers high end signal conditioning. Including a 24-bit Sigma-delta ADC with up to 40 kS/s per channel sampling rate. All analog modules are fully galvanically isolated.
KRYPTON MULTI are multi-channel I/O modules. Firstly, available in single or double width. Dependent on the type and number of input amplifiers. KRYPTON multi-channel devices use 24-bit Sigma-delta ADC and offer up to 20 kS/s per channel sampling rate.
To get the technical breakdown of the signal conditioning units and other components of the KRYPTON® products, click more information. Otherwise contact us, we would love to chat to you about this great product.
Finally, Metromatics proudly sell, service and support the Dewesoft product range in Australia and New Zealand.
Only logged in customers who have purchased this product may leave a review.
Download the Spec Sheet Here.
Test-Engineers-Catalog_EN_V22-1(web)
| Interface | |
| Data interface | EtherCAT® |
| Data Rate | 100 Mbps Full Duplex bus speed |
| Max. Throughput per Chain | From 6 MB/s to 10 MB/s |
| Sync Accuracy | below 1 sample to Sirius® |
| EtherCAT® | Max. Cable Length 100 m |
| Max. Number of Units | 64 or more (power injectors may be required) |
| Data Interface Connection | LEMO 1T EtherCAT® hybrid cable Single cable for data, power and sync, daisy chainable |
| Power | |
| Power Supply | 9 – 48 V DC |
| Environmental | |
| Operating Temperature | -40 to 85°C |
| Storage Temperature | -40 to 85°C |
| Humidity | 5 to 100 % RH |
| IP rating | IP65 / IP67 |
| Shock | Shock: SIST EN 60068-2-27:2009 100 g, 6 ms, half-sine 100x pos./neg in each axis 600x total |
| Vibration | Random vibration: MIL-STD-202G Method 214A, test condition II-D Profile break points: 50 Hz @ 0.025 g²/Hz 100 Hz @ 0.1 g²/Hz 2000 Hz @ 0.1 g²/Hz Profile RMS / Peak = 13.9 g / 41.7 g 8 hrs in each axis, 24 hrs total |
| Rev: 1593507600 | |
| STG | TH | RTD | ACC | LV | LA | DIO | |
| Connectors | DB9, L2B10f | Thermocouple | L0B6f | BNC | BNC | BNC | DB25 |
| #ch per module | 3x, 6x | 8x, 16x | 8x | 4x, 8x | 4x, 8x | 8x | 16xDI, 16xDO 8xDI, 8xDO |
| Data rate / channel | 20 kS/s | 100 S/s | 100 S/s | 20 kS/s | 20 kS/s | 20 kS/s | 40 kS/s |
| Resolution | 24-bit | digital | |||||
| Bandwidth | 0.49 fs | 0.49 fs | 0.49 fs | 0.49 fs | |||
| Voltage ranges | ±10 V, ±1 V, ±100 mV, ±10 mV | ±1 V, ±100 mV | ±1 V, ±100 mV | ±10 V, ±5 V, ±1 V, ±200 mV | ±50 V | ±20 mA | CMOS compatible |
| Input coupling | DC | DC | DC | DC, AC 0.1 Hz, 1 Hz | DC | DC | DC |
| Sensor excitation | 0…15 V max. 0.4 W/ch (45 mA limit) | IEPE 4 mA, 8 mA | 5 V / 300 mA 12 V / 120 mA Vsupply / 200 mA | ||||
| Bridge connection | Full, ½, ¼ 350 Ω, ¼ 120 Ω 3 wire | ||||||
| Programmable shunt | 100 kΩ | ||||||
| IEPE input | DSI-ACC | ||||||
| Resistance | 10 kΩ | ||||||
| Temperature (PTx) | DSI-RTD | PT100, 200, 500, 1000, 2000 | |||||
| Thermocouple | DSI-TH | K, J, T, R, S, N, E, C, B | |||||
| Potentiometer | |||||||
| LVDT | DSI-LVDT | ||||||
| Charge | DSI-CHG | ||||||
| Current | ext. shunt DSI-20mA, DSI-5A | ext. shunt | |||||
| TEDS | |||||||
| Isolation voltage | Differential | 1000 V | 1000 V | Differential | 1000 V | 1000 V | 250 V |
| Power consumption per module | 2.4 W (4 W 120 Ω @ 5 V load) 3xSTG; 5.9 W (8.9 W 120 Ω @ 5 V load) 6xSTG | 2.5 W (8xTH) 4 W (16xTH) | 2.5 W | 4.6 W | 3.5 W (4xLV) 6.7 W (8xLV) | 6.8 W | 2 W |
| Advanced functions | Supports all strain types, TEDS support | High isolation, support of main TC types | High isolation | TEDS support | High isolation, high input range | High isolation, 4-20 mA current loop | |
| Rev: 1602590400 | |||||||
| Analog input | KRYPTONi-4xLV | KRYPTONi-8xLV |
| Input type | Isolated voltage | |
| Number of channels | 4 | 8 |
| ADC Type | 24-bit oversampled SAR with 41 kHz anti-aliasing filter | |
| Sampling Rates | Simultaneous 20k, 10k, 5k, 2k, 1k, 500, 200, 100 S/sec (software-selectable) | |
| Voltage Range | ±50 V | |
| Accuracy | ±0.03 % of reading ±5 mV | |
Typ. SNR (10 kS/sec, -1 dBFS sine wave @ 1 kHz) | 104 dB | |
| Typical noise floor @ 10 kS/sec | -106 dB | |
Type. THD (10 kS/sec, -1 dBFS sine wave @ 1 kHz) | -104 dB | |
Type. SFDR (10 kS/sec, -1 dBFS sine wave @ 1 kHz) | 105 dB | |
| Typical CMR @ 400 Hz / 1 kHz | 105 dB / 94 dB | |
| Gain Drift | Typical 10 ppm/K, max. 20 ppm/K | |
| Offset Drift | Typical 5 μV/K, max. 10 μV/K | |
| Gain Linearity | < 0.01 % | |
| Input Coupling | DC | |
| Input Impedance | 1 MΩ | |
| Noise | 0.7 mVRMS | |
| Overvoltage Protection | In+ to In-: 200 V continuous, 350 Vpeak (100 msec) | |
| Analog input performance | ||
| Bandwidth (-3dB) | 0.49 fs | |
| Alias-free Bandwidth | DC to 0.453 fs | |
| Alias Rejection | -100 dB (all sample rates) | |
| Delay Through ADC | 37 / fs | |
| Oversampling | 32 | |
| Additional Specifications | ||
| Input Connector | BNC | |
| Isolation Voltage | 1000 Vpeak channel/ground & channel/channel | |
| Environmental Rating (see 1) | IP67 | |
| Amplifier type | KRYPTONi-4xLV | KRYPTONi-8xLV |
| Power Consumption | 3.8 W | 6.8 W |
| Weight | 700 g | 1000 g |
| Slice Dimensions | 213 x 39 x 56 mm | 213 x 54 x 56 mm |
| Dimensions with Connectors | 213 x 39 x 66.8 mm | 213 x 54 x 66.8 mm |
| 1) Depending on the mating connector types | ||
| AO | DI | DO | ACC | STG | LV | HV | TH-HV | CNT | |
| Input / Output types | Output: Voltage | Input: Digital | Output: Digital | Input: Voltage, IEPE | Input: Voltage, Strain | Input: Voltage | Input: Voltage | Input: Thermocouple | Input: Digital |
Number of channels per module | 1 | 4 | 4 | 1 | 1 | 1 | 1 | 1 | 1 |
| Connector | BNC | DSUB15HD Male | DSUB15HD Female | BNC | DB9 | BNC | Banana jack | K-type Thermocouple LEMO REDEL | LEMO T-type 7pin female |
| Data rate per channel | 40 kS/s | 40 kS/s | 40 kS/s | 40 kS/s | 40 kS/s | 100 S/s | 20 kS/s | ||
| Resolution | 18 bit | Digital | Digital | 24-bit | 24-bit | 24-bit | 24-bit | 24-bit | 100 MHz timebase 5 ppm, 20 ppm max |
| Bandwidth | 0.49 fs | 0.49 fs | 0.49 fs | 0.49 fs | 0.49 fs | 10 MHz | |||
| Alias-free Bandwidth | 0.453 fs | 0.453 fs | 0.453 fs | 0.453 fs | 0.453 fs | ||||
| Alias Rejection | -100 dB (all sample rates) | -100 dB (all sample rates) | -100 dB (all sample rates) | -100 dB (all sample rates) | -100 dB (all sample rates) | ||||
| Delay Through ADC | 37 / fs | 37 / fs | 37 / fs | 37 / fs | 37 / fs | ||||
| Oversampling | 32 | 32 | 32 | 32 | 32 | ||||
| Voltage ranges | ±10 V | Digital (Low: < 1 V, High: > 2 V) | ±10 V ±5 V ±1 V ±200 mV | ±50 V ±10 V ±1 V ± 100 mV | ±50 V ±10 V ±1 V ±100 mV | ±1000 V | Thermocouple | TTL (Low: <0.8 V, High > 2 V) | |
| Isolation | Galvanic isolation CH, GND | Galvanic isolation CH, GND | 125 Vrms Isolation CH, GND | 125 Vrms Isolation CH, GND | 125 Vrms Isolation CH, GND | CAT III 600 V CAT II 1000 V | CAT III 600 V CAT II 1000 V | ||
| Power supply | 9 – 50 V | 9 – 50 V | 9 – 50 V | 9 – 50 V | 9 – 50 V | 9 – 50 V | 9 – 50 V | 9 – 50 V | 9 – 50 V |
| Power consumption | 2 W | 1.5 W | 2 W | 2 W | 3 W | 1.5 W | 1 W | 1.3 W | 1.2 W |
| Operating temperature | -40 to 85 °C | -40 to 85 °C | -40 to 85 °C | -40 to 85 °C | -40 to 85 °C | -40 to 85 °C | -40 to 85 °C | -40 to 85 °C | -40 to 85 °C |
| Storage temperature | -40 to 85 °C | -40 to 85 °C | -40 to 85 °C | -40 to 85 °C | -40 to 85 °C | -40 to 85 °C | -40 to 85 °C | -40 to 85 °C | -40 to 85 °C |
| Dimensions | 62 x 56 x 29 mm | 62 x 56 x 29 mm | 62 x 56 x 29 mm | 62 x 56 x 29 mm | 62 x 56 x 29 mm | 62 x 56 x 29 mm | 62 x 56 x 36 mm | 62 x 56 x 36 mm | 62 x 56 x 29 mm |
| Weight | 250 g | 250 g | 250 g | 250 g | 250 g | 250 g | 300 g | 300 g | 250 g |
| Rev: 1578868200 | |||||||||
| Interface | |
| Data interface | EtherCAT® |
| Data rate | 100Mbps Full Duplex bus speed |
| Sync Accuracy | below 1 sample to Sirius® |
| EtherCAT® | Max. Cable Length 100 m |
| Max. Throughput per Chain | From 6 MB/s to 10 MB/s |
| Max. Number of Units | 64 or more (power injectors may be required) |
| Data Interface Connection | LEMO 1T EtherCAT® hybrid cable Single cable for data, power and sync, daisy chainable |
| Power | |
| Power Supply | 9 – 50 V DC |
| Power consumption | 1 – 3 W |
| Environmental | |
| Operating Temperature | -40 to 85 °C |
| Storage Temperature | -40 to 85 °C |
| Humidity | 5 to 100 % RH |
| IP rating | IP65 / IP67 (see individual specifications for details) |
| Shock | Shock: SIST EN 60068-2-27:2009 100 g, 6 ms, half-sine 100x pos./neg in each axis 600x total |
| Vibration | Random vibration: MIL-STD-202G Method 214A, test condition II-D Profile break points: 50 Hz @ 0.025 g²/Hz 100 Hz @ 0.1 g²/Hz 2000 Hz @ 0.1 g²/Hz Profile RMS / Peak = 13.9 g / 41.7 g 8 hrs in each axis, 24 hrs total |
| Rev: 1557765000 | |
| Analog Output | |
| Output types | Voltage |
| Number of channels | 1 |
| Output connector | BNC |
| DAC Resolution | 18 bit |
| Update Rate | 1000 S/sec (see 1) |
| Full Scale Output Range | ±10 V (see 2) |
| Accuracy (typ.) | 0.1 % ±1 mV (0 to 20 mA load) |
| Temperature gain drift (typ.) | ±10 ppm/K |
| Temperature offset drift (typ.) | ±5 uV/K |
| SNR @ 1000 S/s output rate | 92 dB (sine wave, 250 Hz, ±9 V) |
| THD | -90 dB |
| Output impedance | 0.45 Ω DC |
| Maximum output current | 20 mA |
| Settling time (0.05 % of set value) | 30 μs @ 1000 Ω load, -10 V to 10 V step |
| Max slew rate | 2.5 V/μs @ 1000 Ω load |
| Max capacitive load (2 % overshoot) | 10 nF |
| Maximum load | 500 Ω |
| Output protection | Short circuit protected |
| Isolation | |
| Power | |
| Power consumption | 2 W (typ.) |
| Environmental | |
| IP rating | IP65 / IP67 (see 3) |
| Physical | |
| Dimensions | 62 x 56 x 29 mm |
| Weight | 250 g |
| 1) Only asynchronous mode is supported in Dewesoft, function generator is not supported | |
| 2) Only DC output voltage, function generator not supported | |
| 3) Depending on the mating connector types | |
| Rev: 1578868200 | |
Reviews
There are no reviews yet.