Strain Gauge Transmitter or Load Cell Transmitter
Firstly, the Acromag TT351 model is a space-saving four-wire Strain Gauge transmitter. Secondly, it converts a four or six wire strain gauge bridge or load cell or millivolt sensor signal to an isolated voltage or current output signal. Also an optional DIN rail bus can deliver primary or redundant power to multiple units.
Above all setup and calibration are fast and easy. With a convenient USB connection to your PC and Acromag’s Windows configuration software.
For instance, the transmitter’s input circuit allows true 6-wire bridge measurement. It includes an adjustable bridge excitation supply (4 to 11V DC) with a remote sense feature. However, sense wires ensure the programmed excitation voltage is measured at the sensor and enable lead-wire compensation. Also the differential input performs true ratiometric conversions for extremely stable measurements. That remain accurate over time and temperature.
In conclusion, Advanced signal processing capabilities, variable range input, and convenient USB programming make this instrument a very versatile strain/load measurement device. Because these transmitters can withstand harsh industrial environments and operate reliably across a wide temperature range with very low drift. They feature RFI, EMI, ESD, EFT, and surge protection plus low radiated emissions.
IMPORTANT: To prevent damage or errors from grounded PCs and surges. Acromag strongly recommends use of their USB-ISOLATOR when configuring a TT350 Series transmitter.
Type: USB Mini-B type socket, 5-pin.
Data rate: 12Mbps. USB v1.1 and 2.0 compatible.
Maximum cable length: 5.0 metres.
USB Transient Protection
Abover all transient voltage suppression on power and data lines.
Not required. Uses Windows HID drivers.
Analog to Digital Converter (ADC)
24-bit S-D A/D converter.
Likewise varies from 13.5 to 20.5 bits per filter and gain selection.
Input Reference Test Conditions
Strain gauge/mV; Excitation = 10V; Rated Output = 1mV/V; Range = ±10mV; Ambient Temperature = 25°C; Power Supply = 24V DC.
Accuracy (overall input to output)
Better than ±0.1% of span, typical. Although, this value does not include sensor errors.
Ambient Temperature Effect
Better than 0.008% of input span per °C (±80ppm/°C).
Normal mode @ 60Hz: -19dB (no filter), -34dB (low filter), >80dB (med/high filter).
Common mode @ 60Hz: -136dB, typical with 100 ohm input unbalance.
Input Overvoltage Protection
Bipolar Transient Voltage Suppressors (TVS).
Firstly, select from basic load cell, two quarter-bridge options, two half-bridge options, three full-bridge options, or millivolts.
Firstly, Bipolar input range is determined from the ± product of the gauge’s rated output. Also the nominal excitation selection (2mV/V x 10V = ±20mV range).
Firstly, the actual input range is up to (user-specified) ±150% of the range. Secondly, this is obtained via the ± product of the gauge’s rated output and the nominal excitation applied.
Likewise accepts gauge rated outputs up to 1mV/V to 10mV/V. Above all, the range of your input signal is the ± product of the excitation voltage and your gauge’s rated output.
±IN at 15M ohms, ±SEN at 73.2K ohms, typical.
Input Lead Resistance
Likewise, module has sufficient overdrive to guarantee 10V bridge excitation with 5 ohms/lead and 100mA of internal excitation current. Also larger lead resistances may limit the maximum achievable internal bridge excitation.
Input Bridge Excitation (Internal)
Adjustable from 4V to 11V, 120mA maximum. Internal excitation must be turned OFF before external excitation supply connection.
Input Bridge Excitation (External)
4V to 11V. The internal excitation must be turned OFF for connection to an external excitation supply.
Digital (Trigger) Input
“Active High” input, 100ms minimum.
15-30V DC (6.65K ohms).
See connection diagram.
Operation (Tare/Alarm Modes)
Firstly, the trigger function is set for “Auto-Tare” mode by default.
Output (DC V/mA)
Ranges: 0-20mA, 4-20mA.
Compliance: 10V minimum (525 ohm load).
Ranges: 0-5V, ±5V, 0-10V, ±10V.
Compliance: 10mA maximum with short circuit protection. 1 ohm output impedance.
Output Response Time to 98% (for step input change)
No filter: 264ms. Medium filter: 472ms.
Low filter: 292ms. High filter: 2547ms.
-40 to 70°C
-40 to 85°C
5 to 95% non-condensing.
Supply | Ptot | Current Draw
9V | 3.05W | 339mA Max.
12V | 3.05W | 254mA Max.
15V | 3.05W | 203mA Max.
24V | 3.05W | 127mA Max.
32V | 3.05W | 95mA Max.
4-way (input/output/trigger/power). Also Input/excitation, analog output, trigger, and power circuits are isolated from each other for up to 1500V AC for 60 seconds or 250V AC continuous.
Shock and Vibration Immunity
CE compliant. UL/cUL listed Class I Division 2 Groups ABCD. ATEX, IECEx certified Zone 2.
II 3 G Ex nA IIC T4 Gc -40°C < Ta < +80°C.
General-purpose enclosure designed for mounting on 35mm “T-type” DIN rail.
Likewise a Self-extinguishing polyamide, UL94 V-0 rated, color light gray. General-purpose NEMA Type 1 enclosure.
Likewise a removable plug-in terminal blocks rated for 12A/250V; AWG #26-12, stranded or solid copper wire.
17.5 x 114.5 x 99.0 mm
0.22 kg packed.
Finally, for more information on Acromag’s TT351 Strain Gauge Transmitter, contact us.