The 6100 Series I/O Modules configure to your specific needs. These modules provide a high degree of flexibility, accuracy and performance. In addition to this, they condition, amplify, filter and output high level signals to external data acquisition systems. Finally users can select modules according to functional and performance requirements for their application.
| Model | Image | Features | Spec Sheet |
|---|---|---|---|
| Model 6120, 2-Channel Strain/Bridge/IEPE Amplifier-Filter-Analog Output |  | Model 6120 is a two-channel, fully automated, high bandwidth, signal conditioning amplifier and filter with dual inputs. The bridge input has voltage and current excitation, automatic balance, shunt calibration and programmable configuration for 1/4, 1/2 and full bridge transducers. The AC-coupled auxiliary input is for ICP/IEPE, dynamic strain and other voltage output transducers. The 6120 also employs an amplifier-per-channel architecture which provides the highest accuracy and completely eliminates crosstalk between channels. | Download Spec Sheet |
| Model 6129 8 Channel AC/DC Coupled IEPE Amplifier Filter Analog Output |  | he 6129 input module has eight channels each providing excitation for IEPE transducers, programmable AC or DC-coupled differential instrumentation amplifier and low-pass filter. Each channel has a buffered analog output that can be selected for wideband or filtered response. | Download Spec Sheet |
| Model 6131 2 Channel Transducer Amplifier Filter Analog Output |  | The 6131 is a two-channel, fully programmable signal conditioning amplifier and filter. It features a plug-on signal conditioning completion card that is available for strain gage, bridge, RTD, potentiometer, voltage-mode charge, voltage and current transducers. Each channel has a programmable gain differential instrumentation amplifier, four 8-pole low-pass filters and a ±10 Volt analog output that can be selected for wideband or filtered response. | Download Spec Sheet |
| Model 6136 4 Channel Charge, IEPE Amplifier Filter Analog Output |  | Model 6136 is a four-channel, programmable charge amplifier, filter, analog output module with a second input for piezoelectric sensors with integrated electronics (IEPE). | Download Spec Sheet |
| Model 6152 4 Channel Strain Bridge Transducer Amplifier Filter Analog Output |  | The 6152 input module has four channels of high performance signal-conditioning amplifiers for strain gages and bridge transducers. Each channel has programmable excitation with remote sensing, voltage calibration, local or remote shunt calibration, programmable gain instrumentation amplifier and four-pole low pass filter. Each channel provides a buffered analog output. | Download Spec Sheet |
| Model 6160 2 Channel Transducer Amplifier Filter Analog Output 300CMV |  | The 6160 is a two-channel signal conditioning amplifier module with 50 kHz or 100 kHz bandwidth and analog outputs. The bridge input is ten-wire shielded with programmable constant voltage or constant current excitation and programmable completion for quarter, half and full bridge transducers. Automatic bridge balancing accommodates large imbalances without limiting dynamic range. | Download Spec Sheet |
| Model 6165 2 Channel Instrumentation Amplifier Filter Analog Output 300CMV |  | The 6165 is a two-channel instrumentation amplifier module. Each channel has isolated input, 100 kHz bandwidth and two outputs that can be filtered or wideband. The input is two-wire shielded and is isolated from the outputs, power and control interface. This gives the user complete freedom to ground the input without creating ground loops that introduce noise and offset errors. The isolation provides for operation with up to ±300 Volts of common mode applied to the input. | Download Spec Sheet |
| Model 6168 2 Channel Transducer Amplifier Filter Analog Output 300CMV |  | The 6168 is a two-channel signal conditioning amplifier module featuring 100 kHz bandwidth and analog outputs. The base board contains both constant voltage with remote sensing and constant current programmable excitation supplies, high-bandwidth instrumentation amplifier with programmable step and variable gain, 4 Hz to 30 kHz, continuously programmable six-pole, low-pass filter and dual buffered outputs. A plug-on module configures the base board for multiple types of transducers including voltage, full and partial bridge, voltage output charge (IEPE) and charge output piezoelectric. | Download Spec Sheet |
For more information, please contact us.
Reviews
There are no reviews yet.